Performance Parts

ID Spring Locator Set of 16 - 1.285" OD, .532" ID, .135" Thickness

ID Spring Locator Set of 16 - 1.300" OD, .505" ID, .040" Thickness

Complete Set of (16) ID Spring Locators.

ID Spring Locator Set of 16 - 1.300" OD, .510" ID, .060" Thickness

ID Spring Locator Set of 16 - 1.340" OD, .570" ID, .100" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.450" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.510" OD, .570" ID, .060" Thickness

Lower Seat for 26120 with .570 Guide

ID Spring Locator Set of 16 - 1.540" OD, .570" ID, .060" Thickness

ID Spring Locator Set of 16 - 1.540" OD, .640" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.550" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.550" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.635" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.655" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

Ignition Heat shrink Terminal kit (165pcs). Contains Ring and Spade terminals; Butt connectors; Female and Male disconnects;Closed end connectors for 22-10 AWG wire(Red,Blue,Yellow).3:1 shrinkage ratio;

• 165 Piece Kit
• Polyethylene insulation (PE) with Copper Terminal Material
• Wire sizes from 10 - 22 AWG

Ignition Primary Wire Extension Kit

• Primary Wire Extension Kit can be used to increase the wire length of our point conversion kits or distributors.
• Kit includes 39" of our quality 20 guage silicone jacketed red and black wire, ring terminals, quick disconnect…

Ignition Wire Marker 8 mm

• Fits 8mm diameter wire

IN-LINE FUEL PULSE DAMPER

• Fittings included for damper/regulator’s and direct mount dampers
• Vacuum fitting and one foot of hose included with all dampers for vacuum referencing
• Assembled and tested in the USA

Inner Bearing Cone-5;200 to 8;000-lb. Axles

• Comes With Nylon Bushings
• Industry Reference EQ-E1

Inner Hood Scoop Pan, No Holes

• Stiff and lightweight
• Washable and reusable
• High air flow

Inspection Cover

• Black Oxide Steel
• Included with LK4000K
• Hardware included

Installation Kit for GM Gen V LT Accessory Drive

• No engine modification required - completely bolt-on
• Cost Effective and Proven Solution
• Utilizes conventional single sided belt

Intake Manifold Spacer

• Cast Aluminum
• Dominator To Square Bore
• 2 1/4" Height

Intake Valve for #60229 & #60329 Cylinder Heads

The Edelbrock #9764 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for #60669 & #60689 Cylinder Heads

The Edelbrock #93661 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for #60779 & #60179 Cylinder Heads

The Edelbrock #9365 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for #60979 Cylinder Heads

The Edelbrock #9774 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.