Performance Parts

Classic Series Front Brake Kit

• Aluminum, 2-Piston, Pad Guided Caliper
• Slot, Drill, Zinc Plated Rotor Finish
• Uses Common FMSI D0412 Brake Pad

Replacement Fuel Filter

• Clear housing for easy viewing
• Replaceable inner filter element design
• For non fuel injected applications

10 AMP Microswitch w/ Extra Large Button and 5/8 in Mount

These switches can be used for many things such as nitrous activation, engaging a transbrake or a rollstop.

CD-5/CD-7 Plug-and-Play Harness for Holley Dominator/HP EFI

Stator - Unmolded - Harley Davidson - 17.8 Amp - 76-80 Big Twin

• Covered by our limited 90 Day warranty

Vapor Guard™ Hose

• Fuel Injection Hose – Rated Maximum 225 PSI

Heater Hose End Fitting - 90° with 3/8" NPT and 3/8" Barb

Edelbrock part #8167 heater hose end is designed to hold up to any plumbing task you have.

Fuel Line - 3/8 Inch Dual Inlet - Chrome

Dual-inlet Holley 4150 4-barrel carburetors with 3/8 inch hose & 9-5/16 inch spacing.

Swivel-Seal® Hose End

• Stainless Retention Pins Allow 360° Adjustment After Installation

Universal Rubber Insert for Axle Hub Dust Cap-2;000-8;000-lb. Axles

• Lippert Rubber Inserts

6 AN Rochester 2 bbl carb fuel inlet fitting

Edelbrock part #8080 Brass Hose Fitting is a 1/4-18" NPT fitting with a 3/8" barb.

Autocross Yellow 2-5/8" Air Fuel Ratio Gauge

• Full sweep provides increased accuracy
• Easy to read 2 5/8" size
• Push-button calibration

Pro Sleeve Boot Guards - Fiberglass Spark Plug Wire Boot Protectors - 4 pack

• Helps protect wires from extreme heat
• Great for use with headers
• 6" Length

Coolant Temperature Sensor for Pro-Flo and E-Street Systems

Edelbrock part #36012 Coolant Temp Sensor for E-Street and Pro-Flo 3 & Pro-Flo 4 systems.

Velocity Black 2-5/8" Air Fuel Ratio Gauge

• Full sweep provides increased accuracy
• Easy to read 2 5/8" size
• Push-button calibration

Spring Rubber

Single Spring Rubber

• Fits springs with 5.0" outside diameters.
• Adds approximately 1.5" of solid height to your spring.
• Made in the U.S.A. and sold individually.

Heater Hose End Fitting - Straight with 1/2" NPT and 3/8" Barb

Edelbrock part #8185 heater hose end is designed to hold up to any plumbing task you have.

Exhaust Tip

• Weld-on
• Angle Cut Rolled Edge
• 304S Stainless Steel Inner Core

Hi-Tech 210 Radius 7.900" Long, .080" Wall, 3/8" Diameter Pushrod Set

Designed for high lift Applications where Pushrod and seat interference are problems at maximum lift, Hi-Tech 210& deg

Linear Tender Spring

Single Spring

• Available in Linear or Progressive Rates
• Each Spring Individually Tested
• Highest Linearity and Guaranteed Consistency

Black Econ-O-Fit Hose Clamp

• Fits Radiator Hoses

Velocity White 2-5/8" Fuel Level Gauge (240-33 Ohm)

• Easy to read 2 5/8" size
• 240 ohms empty, 33 ohms full
• Flat glass lens

Performance Ceramic Disc Brake Pad

• Increased Rotor Life
• Ultra-Low Dust
• Extremely Quiet

Pro-Flo Multi-Point Replacement Calibration Module

The Edelbrock 3519 is a new calibration module that will be a replacement or service part for any Pro-Flo kit.

Brakes Premium Aluminum 5-Lug Wheel Spacers – 5x4.50, 5x4.75 Bolt Patterns

• Widen Track
• Zinc plated steel
• Sold in Pairs