Performance Parts

4 Pin RGB Male/Female Connector

• Allows connection to In-line controller without need to solder wires

4 X 9in. Oval Straight-Through Performance Exhaust Muffler

• 100% Stainless Steel
• Mufflers are Bi-Directional
• Delivers a Smooth, Deep Tone

500A Dual Channel Analog Current Sensor

• Good accuracy for high and low current.
• The inner diameter is 21.55mm.
• Operating Temperature Range of -40 to 257 Fahrenheit.

50 Lb/Hr Fuel Injector (Qty 8)

The Edelbrock #15901 injectors are Bosch style, standard long length (60mm O-ring to O-ring dimension), and are high impedance 50 lb/hr at 43.5 psi (300 Kpa).

50Mm Lower Spring Seat

5/8 Cable w/ Threaded Ends for Pre-76 Vehicles Running Speedometer Control Unit

Speedometer Control Unit Adapters

5in. 90deg. Bend Performance Exhaust Pipe

• Mandrel bent tubing for smoother transitions
• CNC precision robotic manufacturing techniques
• Durable corrosion-resistant stainless steel construction

5 Male to -4 Male Union Reducer - Stainless Steel

• Available for Any Plumbing Situation And Many Custom Applications.

60 Lb/Hr Fuel Injector (Qty 8)

The Edelbrock #15903 is a 60 pound-per-hour Fuel Injector for the E-Street TBI, ProFlo EFI, and Edelbrock supercharger systems.

6 AN Male to 14mm x 1.50 Male

• Black Anodized

6AN Male x 3/8" SAE Quick-Disconnect Female Threaded Cap Fitting, Blue - 25 Pack

• 6061-T6 Aluminum
• Positive Seal At Maximum Operating Pressures

7 Degree Steel Retainer Set of 100 for 3/8" Valve w/ 1.437"-1.500" Spring

Valve springs with larger diameters require retainers to handle the higher pressures developed by the springs.

7 Degree Titanium Retainer for 26926 Spring w/ 8mm Valve Stem

Upgrading to these 7& deg

7 Degree Titanium Retainer for 7245 Dual Conical Spring

Upgrading to COMP Cams titanium valve spring retainers will often allow you to gain speed and power because titanium retainers are lighter and as strong as than most Steel ones.

7 Degree Titanium Retainer Set of 100 for 26926 Spring w/ 8mm Stem

Upgrading to these 7& deg

8AN Male to -6AN Male Forged Y-Block

• Available for Any Plumbing Situation And Many Custom Applications

8 Forged "L" B-Nut / No Ext

• Replacement Component for Kits # AT101285ERL & AT101286ERL

8mm Spiro-Pro 30 Ft Coil Yellow

• Color: Yellow
• 30 ft. Coil
• 350-Ohm per foot resistance Spiral Wound Core

8mm Spiro-Pro Repair Kit Lt1 Red

• Color: Red
• Taylor repair wire kits provide easy replacement for damaged wire
• HEI and socket style distributor ends provided in kits

90 Degree 3/8" Hose to 1/4" NPT Male Elbow

• Must use PTFE tape or sealing compound during assembly. Hose side to be used with hose clamp. DO NOT overtorque.

90 Degree Blue Silicone Plug Boot

• 90° Silicone Boots
• Bulk Pack of 25
• All boot/terminals fit 8-10.4mm

90-Degree Transition Coupler, Black, Silicone, 3.00in to 3.25in

• Allows for easy routing of complex coolant or intercooler pipes
• 100-percent silicone construction
• Constructed from four layers of silicone with embedded heat-resistant fibers

94â„¢ Series Carburetor Main Jet - .054" (Qty 2)

The Edelbrock 94 #1165 Carburetor Jets .053" Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94's and its later variations.

Acc Chrome GM Style Oil Fill Tube

Edelbrock part #4803 Oil Fill Tube and matching push-in Breather is an original style for vintage manifolds with a 1-1/4" oil breather hole.

Accelerator Pump Cover

• Genuine Holley Quality Parts