Performance Parts

Low-Mount LS Accessory Drive Bracket - Driver's Side P/S & Alt Bracket Black

• Fits Middle and Long Accessory Spacing
• Installation Kit 21-4 Required w/ Long Spacing
• Cost Effective Solution

LS Accessory Drive Bracket - Installation Kit for Middle Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets

LS COOLING MANIFOLD RAW

• Genuine Holley Quality Parts

LS COOLING MANIFOLD RAW A/C Delete

• Genuine Holley Quality Parts

Machined Steel Set of 100 - 7 Degree, 11/32", Single Groove Race Locks

Most people believe that the tang inside a valve lock holds the retainer and valve spring in place while the engine is running, but this isn't the case.

Machined Steel Set of 12 - 7 Degree, 11/32", Single Groove Race Locks

Includes 12 Pairs of Machined Steel Race Locks: 1 Groove, 7& deg

Magnet Sleeve (only) for 1562 Ignitor Kit

• Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
• Replacement Magnet Sleeve for PerTronix 1562 (Service Part Only)
• Rotating cobalt magnets trigger a Hall Effect integrated circuit; no points to burn; no moving parts to wear out.

Magnum Polylock Set for 7/16" Rocker Stud

Designed for ultimate strength and locking force High Energy and Magnum polylocks are best for moderate lift and spring pressure Applications Hi-Tech Polylocks work well in all high end Race applications.

Main Harness X-Series AEMnet Gauge

• Direct harness replacement for 30-0312 AEMnet gauge
• High quality DTM connectors
• Color coded harness to make installation easier

MAP Sensor Assembly for Atomic TBI

Atomic TBI factory replacement MAP sensor.

Moal Bomber 2-1/8" Exhaust Gas Tempature Gauge

• stainles steel braided wire, included- Thermocouple amplifier included

Moal Bomber 2-1/8" Outside Air Tempature Gauge

• Pushbutton calibration
• Small 2 1/8" hole size
• Installation hardware included

Non-Adjustable Pivot Ball Stud

• Sold Individually
• Fits 1979-2014 Ford Mustang & 1979-1986 Mercury Capri
• Non-Adjustable Ball Stud

Nostalgia 2-5/8" Cylinder Head Temperature Gauge

• Nostalgia VT Series
• Standard stainless steel low step bezel
• Flat glass lens

Nostalgia VT 2-1/8" Outside Air Tempature Gauge

• Small 2 1/8" hole size
• Pushbutton calibration
• Installation hardware included

Nostalgia VT 5" Speedtachular Speedometer Gauge

• Nostalgia VT Series
• Stainless Low Step Bezel
• Flat Glass Lens

Nylon Fuel Bowl Screw Gasket

Nylon Fuel Bowl Screw Gasket - Includes (8) gaskets

Oil Pickup Tube Assembly - Ford Godzilla 7.3L

• Direct replacement for Holley Godzilla oiling system

End Link Kit

Pair of Adjustable End Links

• Chromoly Rod Ends and Easy to Adjust Hex Bodies
• Sold as a pair
• Made in the U.S.A.

Park Brake Cable

• Designed Specifically for Baer's Classic Series Brake Kit
• Attaches to OE Front Cable Section
• Direct Fit, No Cutting Required

Park Brake Cable

• Attaches to OE Front Cable Section
• Direct Fit, No Cutting Required
• Stainless Steel Cable with a Premium Housing for Long Cable Life

Park Brake Cable

• Attaches to OE Front Cable Section
• Direct Fit, No Cutting Required
• Stainless Steel Cable with a Premium Housing for Long Cable Life

Park Brake Cable

• Designed Specifically for Baer's Classic Series Brake Kit
• Attaches to OE Front Cable Section
• Direct Fit, No Cutting Required

Performance Exhaust 063-1625 Catalytic Converter Gasket for Part Number 1625

• Rated up to 1100 F
• Handles exhaust pressures up to 3700 psig
• Designed for an exact port match with JBA headers

Performance Street 1.290" OD Beehive Spring; 1.800" Installed Height; 1 Spring

With a .600" maximum lift, these Beehive Valve Springs were designed for hydraulic Roller cams.