Performance Parts

75 Series Pro-filter 2 8AN Male In/Out, 100 Micron Element With Black Finish

• high flow, low pressure drop
• Compatible with E85 fuels
• Carbureted or EFI applications

90-Degree Silicone Transition Coupler, 2.00-in to 2.25-in, Black

• Allows for easy routing of complex coolant or intercooler pipes
• 100-percent silicone construction
• Constructed from four layers of silicone with embedded heat-resistant fibers

Adel Mount Clamps - 3/4 Inch - 6 Pieces

Insulating with Adel 75005 compound means easier mounting of wire, fuel hoses, etcetera, to any solid surface.

All American Nickel 2-1/8" Cylinder Head Temp Gauge

• Push button calibration
• Completely electric
• Small 2 1/8" hole size

BRACKET Spacer Kit LT4 Power Steering Add-on Kits-Black

• Genuine Holley Quality Parts

Extreme+ Brake System Front

• Powder Coated Finish
• Staggered Pistons to Minimize Uneven Pad Wear
• Dual Seals, Dust/Weather & Pressure

Line Adapter Manifold for SD7 A/C Compressor - SBF, Driver Side Exit

• Allows optional routing for A/C lines with Holley's SBF accessory drive

Power Steering Hose End

• Stainless Steel (or Nickel Plated, or Black Chromate Finish – depending on the part number)

Metric Coilover Spring

Single Spring

• Available in Linear or Progressive Rates
• Each Spring Individually Tested
• Highest Linearity and Guaranteed Consistency

Suspension Kit, coil springs / shock absorbers; Kit (Front+Rear)

Suspension Kit, coil springs / shock absorbers

Regulator Rebuild Kit

• Fuel Pressure regulator rebuild kit for Holley 12-840 regulator
• Includes diaphragm and spring

SPE-4358 Fan Shroud

• Easy to install
• Hardware included
• 20 inch diameter

10 Superlock Steel Retainer for 1.437"-1.500" OD Valve Spring

Valve springs with larger diameters require retainers to handle the higher pressures developed by the springs.

AutoCross Yellow 2-5/8" Full Sweep Water Temp Gauge

• Easy to read 2 5/8" size
• Push-button calibration
• Temperature sending unit included

Check Valve - 1/4 in. FNPT x 1/4 in. MNPT - SMC # AKB02B-N02S

• Check Valve 1/4 In FNPT x 1/4 In MNPT - SMC AKB02B-N02S

DOT4 High Performance Brake Fluid, 16.9oz/500ml Bottle

• Minimum Dry Boiling Point: 608°F (320°C)
• Bottle Size: 16.9oz (500ML)
• Single Bottle

Fuel Filter Replacement Element

• Includes O-rings

GAUGE; AIR/FUEL RATIO-PRO; 2 1/16in.; 10:1-20:1; DIGITAL W/PEAK/WRN; ULTRA-LITE

• 12 And 16V Compatible
• 0-4V Data Output Feed For ECU
• 10:1-20:1 AFR Range

GAUGE; BOOST; 2 1/16in.; 35PSI; STEPPER MOTOR W/PEAK/WARN; BLK/CHROME; SPEK-PRO

• 7 Color User Selectable
• Precision 280 Brushless Stepper Motor
• High And Low Warning Settings

GAUGE; SPEEDO; 3 3/8in.; 260MPH/260KM/H; ELEC PROGRAM; DIGITAL; SLVR W/RED LED

• E-Z View Digital LED Display
• Programmable w/EZ Cal System-MPH Or KM/H
• Simple Push Button 2 Mile Drive Calibration

GAUGE; TACH; 5in.; 9K RPM; PEDESTAL; DATALOGGING; ULTIMATE III PLAYBACK; SILVER

• 12 And 16V Compatible
• Optimize Your Engines Power Band
• User-Programmable Shift Light

G/Stock 2-1/8" Volt Gauge

• Push-button calibration
• Easy to read 2 1/8" size
• Installation hardware included

Hi-Tech 9.750" Long, .080" Wall, 3/8" Diameter Pushrod Set of 8

The Pushrod is one of the most important pieces of the valve train, but all too often it's taken for granted. pushrods not only have to be strong enough to not fail, bend or burn up at the ends, they must also match the frequency of all the rest of the pa parts in the valve train, as well as the rpm at which the engine will be run.

Hi-Tech One-Piece 8.280" Long, .135" Wall, 3/8" Diameter Pushrod Set of 8

With a massive 37 percent increase in stiffness over standard .080" wall Pushrods, Hi-Tech 210& deg

Nostalgia VT 2-5/8" Full Sweep Water Temperature Gauge

Quality, Service and Value are not new to us.