Performance Parts

HVAC Filter; 16 x 16 x 1, MERV 11

• Merv 11 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC Filter; 20 x 25 x 2, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HYDRAMAT (3X15) RECT - 19MM OUTLET OFFSET

• Unique internal reservoir assists in keeping fuel available at the pickup even under extreme fuel slosh conditions
• Also acts as a 15 micron pre-filter eliminating the need for a separate filter before the fuel pump
• Can be folded and compressed for easy installation through a variety of fuel cell openings

Idler Bearing for Hi-Tech Belt Drive Systems

Replacement Idler Bearing for Hi-Techâ„¢ Belt Drive Systems.

Idler Pulley

• Genuine Holley Quality Parts

ID Spring Locator - 1.285" OD, .532" ID, .040" Thickness

ID Spring Locator - 1.285" OD, .525" ID, .040" Thickness

ID Spring Locator - 1.285" OD, .805" ID, .135" Thickness

ID Spring Locator - 1.285" OD, .805" ID, .135" Thickness - Single

ID Spring Locator Set of 16 - 1.350" OD, .515" ID, .050" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

Inspection Cover

• Hardware included

Intake Valves for #60979 Cylinder Heads

The Edelbrock #9779 Intake Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

inTune i2/i3 Replacement Cable

• Works with later i1000 devices
• Plug and play design
• Easy installation

Late Model USCAR Fuel Pump Module Mounting Ring - Stainless Steel

• Available in 6061 Aluminum, Mild Steel, and 304 Stainless Steel – Choose Same Material as Fuel Tank for Easy Welding

LOWER GEAR, FOR 6502

Lower Gear for #6502 Hi-Tech Belt Drive System

LOWER SEAL,FOR 6502/6506 BELT

Lower Seal for #6502 and #6506 Hi-Tech Belt Drive

Low-Mount LS Accessory Drive Bracket - Driver's Side P/S & Alt Bracket Black

• Fits Middle and Long Accessory Spacing
• Installation Kit 21-4 Required w/ Long Spacing
• Cost Effective Solution

LS Accessory Drive Bracket - Installation Kit for Middle Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets

LS COOLING MANIFOLD RAW

• Genuine Holley Quality Parts

LS COOLING MANIFOLD RAW A/C Delete

• Genuine Holley Quality Parts

Machined Steel Set of 100 - 7 Degree, 11/32", Single Groove Race Locks

Most people believe that the tang inside a valve lock holds the retainer and valve spring in place while the engine is running, but this isn't the case.

Machined Steel Set of 12 - 7 Degree, 11/32", Single Groove Race Locks

Includes 12 Pairs of Machined Steel Race Locks: 1 Groove, 7& deg

Magnet Sleeve (only) for 1562 Ignitor Kit

• Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
• Replacement Magnet Sleeve for PerTronix 1562 (Service Part Only)
• Rotating cobalt magnets trigger a Hall Effect integrated circuit; no points to burn; no moving parts to wear out.

Magnet Sleeve (replacement) for PerTronix Industrial Electronic Distributor

• Replacement Magnet Sleeve for #D33-03AM Industrial Distributors

Magnum Polylock Set for 7/16" Rocker Stud

Designed for ultimate strength and locking force High Energy and Magnum polylocks are best for moderate lift and spring pressure Applications Hi-Tech Polylocks work well in all high end Race applications.

Main Harness X-Series AEMnet Gauge

• Direct harness replacement for 30-0312 AEMnet gauge
• High quality DTM connectors
• Color coded harness to make installation easier

MAP Sensor Assembly for Atomic TBI

Atomic TBI factory replacement MAP sensor.