Performance Parts

High Quality Rocker Studs 7/16" (Qty 16)

The Edelbrock high-quality rocker studs #8593 7/16" (Set of sixteen) are used in Edelbrock cylinder heads requiring screw-in studs.

High Volume Fuel Rail Banjo Fitting Without Hole

• Sold each
• black anodized finish
• Fuel rails are sold separately

Hi-Tech 11.000" Long, .080" Wall, 3/8" Diameter Pushrod

The Pushrod is one of the most important pieces of the valve train, but all too often it's taken for granted. pushrods not only have to be strong enough to not fail, bend or burn up at the ends, they must also match the frequency of all the rest of the pa parts in the valve train, as well as the rpm at which the engine will be run.

Hi-Tech 7.200" Long, .105" Wall, 5/16" Diameter Pushrod

With a 17 percent increase in stiffness over standard .080" wall Pushrods, Hi-Tech .105 Wall pushrods feature seamless chromemoly tubing that ensures even greater strength and durability.

Hi-Tech Rocker Stud w/ 7/16" Base Thread and 1/2" Rocker Thread

Hi-Tech Rocker Stud with 7/16" Base Thread and 1/2" Rocker Thread

Hose Clamp

• Attach To Supporting Structure

Hose Separator

• 6061-T6 Aluminum
• Fits 6 AN ProClassic Hose
• Red Anodized

Hose/Wire Wrap

• Easy Installation And Removal
• Lightweight
• Self-Wrapping

Hot Rod 2-1/8" Gear Select W/OD

Quality, Service and Value are not new to us.

Hot Rod 2-1/8" Oil Temperature Gauge

• Hot Rod Series
• 2 1/8" Oil Temperature
• Curved Glass Lens

Hot Rod 2-5/8" Fuel Pressure Electric Gauge (15 PSI)

Quality, Service and Value are not new to us.

HP Plus Disc Brake Pad

• HP Plus Compound
• Wide Temperature Range
• Fade Resistant

HVAC Filter; 12 x 20 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

Inner Bearing Race-3;500 to 4;400-lb. Axles

• Industry Number68111
• Pairs With Bearing Cone PN[L68149]
• 1-3/8 in. Shaft Diameter

LED Dimming Switch / Potentiometer

• Allows control over brightness of LED products without electronic controller

LINE ADAPTR-MNFLD FOR SD7 A/C COMP

• Manifold adapter allows connection to custom A/C lines

Low-Mount LS Accessory Drive Bracket - Driver's Side P/S & Alt Bracket Polished

• Fits Middle and Long Accessory Spacing
• Installation Kit 21-4 Required w/ Long Spacing
• Cost Effective Solution

LS Accessory Drive Bracket - Installation Kit for Long Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets

LS COOLING MANIFOLD BLACK

• Genuine Holley Quality Parts

LS COOLING MANIFOLD POLISHED

• Genuine Holley Quality Parts

LS High-Mount A/C Accessory Drive Bracket - Passenger's Side A/C Bracket

• The most cost effective LS bracket solution on the market!
• Utilizes commonly available and affordable GM A/C compressors
• Accepts GM R4 compressor (Sanden version now available)

LT COOLING MANIFOLD BLACK

• Genuine Holley Quality Parts

LT COOLING MANIFOLD POLISHED

• Genuine Holley Quality Parts

MAGNETIC TRIGGER; DRIVESHAFT RPM; REPLACEMENT; FOR ULTIMATE TACHOMETER

• For Use w/Ultimate And Ultimate II Tachometers Only
• Not Compatible w/Ultimate III Or DL Tachometers

Magnet Sleeve (only) for 1143 Ignitor Kit

• Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
• Replacement Magnet Sleeve for PerTronix 1143 (Service Part Only)
• Rotating cobalt magnets trigger a Hall Effect integrated circuit; no points to burn; no moving parts to wear out.