Performance Parts

Hot Rod 2-1/8" Fuel Level Gauge (1975-2010 Ohm)

• Hot Rod
• Standard Low Step Bezel
• Curved Glass Lens

Hot Rod 2-1/8" Oil Temperature Gauge

• Small 2 1/8" hole size
• Pushbutton calibration
• Installation hardware included

Hot Rod 2-1/8" Oil Temperature Gauge

Quality, Service and Value are not new to us.

Hot Rod 2-1/8" Outside Air Tempature Gauge

• Small 2 1/8" hole size
• Pushbutton calibration
• Installation hardware included

Hot Rod 2-5/8" Fuel Level Gauge

• Flat glass lens
• 0 ohms empty, 30 ohms full
• Easy to read 2 5/8" size

Hot Rod 2-5/8" Short Sweep Water Temperature Gauge

Quality, Service and Value are not new to us.

Hot Rod Kit 2.5in O.D. T-304 Stainless Steel

• If clamping, use wide (2 bolt style) band clamps
• If clamping, use wide (2 bolt style) band clamps
• Brushed finish can be polished prior to installation

HRT Blower

The HRT Camshaft Series uses the newest and most advanced lobe designs from COMP Cams in order to produce some of the highest average power and torque increases available for turbo and supercharged engines.

Hump Hose Coupler, Black, Silicone, 1.50in

• 100-percent silicone construction
• Heat-resistant embedded fibers
• High heat and pressure tolerances

Hump Hose Coupler, Black, Silicone, 1.75in

• 100-percent silicone construction
• Heat-resistant embedded fibers
• High heat and pressure tolerances

Hump Hose Coupler, Black, Silicone, 2.00in

• 100-percent silicone construction
• Heat-resistant embedded fibers
• High heat and pressure tolerances

Hump Hose Coupler, Black, Silicone, 2.25in

• 100-percent silicone construction
• Heat-resistant embedded fibers
• High heat and pressure tolerances

Hump Hose Coupler, Black, Silicone, 2.75in

• 100-percent silicone construction
• Heat-resistant embedded fibers
• High heat and pressure tolerances

HVAC Filter; 18 x 20 x 1, MERV 11

• Merv 11 rating
• Easy to clean and reuse
• Lifetime limited warranty

HYDRAMAT (3X8) 19MM Offset

• Unique internal reservoir assists in keeping fuel available at the pickup even under extreme fuel slosh conditions
• Also acts as a 15 micron pre-filter eliminating the need for a separate filter before the fuel pump
• Can be folded and compressed for easy installation through a variety of fuel cell openings

ID Spring Locator - 1.500" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator - 1.510" OD, .630" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator - 1.540" OD, .570" ID, .060" Thickness

Made from hardened steel, this locator uses an inboard locating shoulder to center the seat and hold the spring in place.

ID Spring Locator - 1.540" OD, .640" ID, .060" Thickness

Made from hardened steel, this locator uses an inboard locating shoulder to center the seat and hold the spring in place.

ID Spring Locator - 1.550" OD, .570" ID, .040" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator - 1.550" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 100 - 1.270" OD, .520" ID, .060" Thick

The older style standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

ID Spring Locator Set of 16 - 1.285" OD, .805" ID, .135" Thickness

ID Spring Locator - 1.285" OD, .805" ID, .135" Thickness - Set of 16

ID Spring Locator Set of 16 - 1.300" OD, .805" ID, .205" Thickness

ID Spring Locator - 1.300" OD, .805" ID, .205" Thickness - Set of 16

ID Spring Locator Set of 16 - 1.540" OD, .640" ID, .060" Thickness