Performance Parts

GAUGE; SPEEDOMETER; 5in.; 160MPH; ELEC. PROGRAMMABLE; ULTRA-LITE II

• Modern LED Through-The-Dial Lighting
• Simple Push Button 2 Mile Drive Calibration
• Incl. Mounting Hardware/Instructions

GAUGE; VOLTMETER; 2 1/16in.; 18V; ELECTRIC; C2

• Futuristic Red Point Look
• 1 Year Limited Warranty
• 12 And 16 Volt Compatible

GPS Speed Sensor

• Simple wiring
• 8000 ppm or 16000 ppm output
• Compact size

Hardened Steel 7 Degree, 11/32", Single Groove Street Lock

Includes 1 Pair of hardened Steel Street Locks: 1 Groove, 7& deg

Heat Shield Mounting Kit 8-Pack

• 1/2 in. Tall Stainless Standoffs
• Includes Mounting Hardware
• Includes 8 Stainless Standoff Brackets

Heat Shrink Terminal Kit

• Waterproof
• Shrink Ratio of 3:1
• 165 Piece Kit

High Energy 8.234" Long, 5/16" Diameter Pushrod

High Energy pushrods from COMP Cams are an affordable, high quality solution when building street rods, RV's and daily drivers.

High Quality Rocker Studs 7/16" (Qty 16)

The Edelbrock high-quality rocker studs #8593 7/16" (Set of sixteen) are used in Edelbrock cylinder heads requiring screw-in studs.

High Volume Fuel Rail Banjo Fitting Without Hole

• Sold each
• black anodized finish
• Fuel rails are sold separately

Hi-Tech 11.000" Long, .080" Wall, 3/8" Diameter Pushrod

The Pushrod is one of the most important pieces of the valve train, but all too often it's taken for granted. pushrods not only have to be strong enough to not fail, bend or burn up at the ends, they must also match the frequency of all the rest of the pa parts in the valve train, as well as the rpm at which the engine will be run.

Hi-Tech 7.200" Long, .105" Wall, 5/16" Diameter Pushrod

With a 17 percent increase in stiffness over standard .080" wall Pushrods, Hi-Tech .105 Wall pushrods feature seamless chromemoly tubing that ensures even greater strength and durability.

Hi-Tech Rocker Stud w/ 7/16" Base Thread and 1/2" Rocker Thread

Hi-Tech Rocker Stud with 7/16" Base Thread and 1/2" Rocker Thread

Hose Clamp

• Attach To Supporting Structure

Hose Clamp

• Attach To Supporting Structure

Hose Clamp

• Attach To Supporting Structure

Hose Separator

• 6061-T6 Aluminum
• Fits 6 AN ProClassic Hose
• Red Anodized

Hose/Wire Wrap

• Easy Installation And Removal
• Lightweight
• Self-Wrapping

Hot Rod 2-1/8" Gear Select W/OD

Quality, Service and Value are not new to us.

Hot Rod 2-1/8" Oil Temperature Gauge

• Hot Rod Series
• 2 1/8" Oil Temperature
• Curved Glass Lens

Hot Rod 2-5/8" Fuel Pressure Electric Gauge (15 PSI)

Quality, Service and Value are not new to us.

HP Plus Disc Brake Pad

• HP Plus Compound
• Wide Temperature Range
• Fade Resistant

Inner Bearing Race-3;500 to 4;400-lb. Axles

• Industry Number68111
• Pairs With Bearing Cone PN[L68149]
• 1-3/8 in. Shaft Diameter

LINE ADAPTR-MNFLD FOR SD7 A/C COMP

• Manifold adapter allows connection to custom A/C lines

Low-Mount LS Accessory Drive Bracket - Driver's Side P/S & Alt Bracket Polished

• Fits Middle and Long Accessory Spacing
• Installation Kit 21-4 Required w/ Long Spacing
• Cost Effective Solution

LS Accessory Drive Bracket - Installation Kit for Long Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets