Performance Parts

Non Stick Red Fuel Bowl Gaskets

Non Stick Red Fuel Bowl Gaskets - For most carburetors with a metering block (4150/4160 style, Q, RQ, SS, HR, QfX Series) - Sold in pairs

Nostalgia 2-1/8" Boost Electric Gauge (30 PSI)

• Nostalgia VT Series
• 30psi
• Flat glass lens.

Nostalgia 2-1/8" Pyrometer Full Sweep

• Nostalgia VT Series
• Standard stainless low step bezel
• Flat glass lens.

Nostalgia VT 2-1/8" Fuel Level Gauge

• Nostalgia VT 2 1/8" Fuel Gauge 240-33 OHM with Stianless High Step Bezel Curved Glass Lens

Nostalgia VT 2-1/8" Fuel Level Gauge

• Small 2 ⅛" hole size
• Push-button calibration
• Installation hardware included

Nostalgia VT 2-1/8" Fuel Level Gauge (0-30 Ohm)

• 2 1/8" Fuel Gauge
• 0-30 OHM
• Flat Glass Lens

Nostalgia VT 2-1/8" Volt Gauge

• Push-button calibration
• Installation hardware included
• Easy to read 2 1/8" size

Nostalgia VT 2-5/8" Air Fuel Ratio Gauge

• Full sweep provides increased accuracy
• Easy to read 2 5/8" size
• Push-button calibration

Nostalgia VT 2-5/8" Air Pressure Gauge

• Pressure transducer included
• Easy to read 2 5/8" size
• Pushbutton calibration

Nostalgia VT 3-3/8" Speedometer Gauge

Quality, Service and Value are not new to us.

Nostalgia VT 4-5/8" Speedtachular Speedometer Gauge

• Built-in ECM filter signal switch

Nylon Fuel Inlet Gasket 7/8"

Nylon Fuel Inlet Gasket 7/8" - sold in pairs

Oil Line Stay, Gold, -10AN

• High quality 6061 aluminum construction
• Fits all rubber or stainless steel -10AN lines
• Prevents oil lines from rubbing

Oil Transfer Tube - Ford Godzilla 7.3L

• Direct replacement part for Holley Godzilla swap oiling system

Outer Bearing Race- 5;200 to 6;000-lb. Axles

• Industry Number68111
• Pairs With Bearing Cone PN[L68149]
• 1-3/8 in. Shaft Diameter

Outside Air Temperature Sender

Quality, Service and Value are not new to us.

Oxygen (O2) Sensor Weld-In Bung (18 x 1.5mm Internal Threads)

The Edelbrock #91172 Weld-In Oxygen Sensor Bung is for All Edelbrock Pro-Flo EFI Systems, E-Street EFI, QwikData 2, or any application requiring an Oxygen Sensor installed in the Exhaust system.

Performance Air Intake System

• Guaranteed to increase horsepower
• Replaces entire factory air intake system
• K& N No-Hassle Lifetime Limited Warranty

Performance Carb Base Gasket - 4-Hole - Bulk Packaged with UPC Label

• 1/16" Thick
• Precision Die Cut For Excellent Seal And Fit
• Can Be Trimmed If Necessary

Performance Carburetor Base Gasket

• Can Be Trimmed If Necessary
• Cellulose/Nitrile Performance Series Gasket Material
• 1/16" Thick

Performance Carburetor Base Gasket - Open Center - Skin Package

• Precision Die Cut For Excellent Seal And Fit
• Can Be Trimmed If Necessary
• Cellulose/Nitrile Performance Series Gasket Material

Performance Ceramic Disc Brake Pad

• Increased Rotor Life
• Ultra-Low Dust
• Extremely Quiet

Performance Collector Gaskets

• Withstands Extreme Exhaust Heat
• Superior Tensile Strength
• Resists Deteriorating

Performance Collector Gaskets

• Withstands Extreme Exhaust Heat
• Superior Tensile Strength
• Resists Deteriorating

Performance Exhaust 31650-1ST 2.5" 304 Series Stainless Steel 2 bolt Starter Tubes w/O2 sensor bungs

• 2.5 inch length
• 304 Stainless Steel
• 2-Bolt Starter Tubes