Engine Sensors

150 PSIg Brass Sensor Kit

• Accurate with 3% margin for error.
• Weather resistant connector and pins included
• Analog Data Scaled in Charts

15 PSIa/1 Bar Stainless Sensor Kit

• Stainless-steel sensors accurate to within 1% of full scale (pressure sensors)
• Connector and pins included
• Analog Data Scaled in Charts

1-Bar MAP Sensor #36021 for Chevy LS3 applications

The new Edelbrock 1-Bar Manifold Absolute Pressure (MAP) Sensor #36021 is designed to fit Chevrolet LS3 applications that use an Edelbrock LS3 XT intake manifold or any other factory-style intake that has a 12mm MAP sensor port hole.

2000 PSIg Stainless Sensor Kit

• Accurate to 1% margin of error.
• Includes 1/8" NPT to -4 AN adapter included
• Weather resistant connector and pins included

ATOMIC TBI, COOLANT TEMP SENSOR

• Replacement coolant temperature sensor for Atomic EFI system

Atomic TBI, Fuel Pressure Sensor

Atomic EFI Support Component

Bosch LSU 4.2 Wideband UEGO Installation Kit

• No calibration required when used with our gauges.
• Accurate to 0.1 AFR
• Sold as a kit

Bosch Replacement UEGO Sensor

• Never requires free-air calibration when used with an AEM Controller and connector plug.
• Connector and pins included
• Replacement sensor only

Channel 2, O2 Sensor, Harness, and Bung Kit for Part Number 7766

The Dual Wide-Band O2 sensor module is capable of measuring AFR as low as λ = 0.5 (7.35:1 Gasoline AFR equivalent).

EAS Replacement EGT LEAD - 15 Inch

• EAS Accessory
• Easy Plug and Play
• Monitor EGT's with your device

EAS Temperature Sensor - -40-300 Degrees Fahrenheit

• Monitor temps on your vehicle
• -40° - 300° Range
• Easy Setup with EAS

GM Oil Pressure Bushing Kit

Our brass angled-bushing kits allows for easy installation on most GM or Ford engines.

K-Type Closed Tip Thermocouple

• Comes with everything you need
• Includes K-Type Closed Tip Thermocouple, Inconel sheath, 1/8" NPT compression fitting, 10-foot extension harness
• Sold individually

K-Type Thermocouple 10' Extention Harness

• Cut to Fit Extension
• 2 X 4-40 Hex Nut, 2 X 4-40 Screw & 6" Heat Shrink Tubing
• Sold Individually

Manifold Absolute Pressure Sensor #3542 Upgrade For ProFlo4 Boosted Applications

Edelbrock part #3542 is a 2-Bar MAP sensor is an upgrade component for use with ProFlo4 boosted applications.

Manifold Absolute Pressure Sensor #3547 Upgrade For ProFlo4 Boosted Applications

Edelbrock part #3547 T-MAP Sensor Conversion Harness Kit is to install a single combination Inlet Air Temp (IAT) & Manifold Absolute Pressure (MAP) sensor in place of existing separate IAT and MAP sensors.

MAP Sensor 2-bar for blown/turbo

• Applications up to 15 lbs of boost.
• Stock connector.

MAP Sensor 2-bar for blown/turbo applications

• Applications up to 15 lbs of boost.
• For use with MSD controls.

Oil Pressure Sender (80 PSI)

Oil Pressure Sender 80 PSI

Pro-Flo 3 Fuel Sensor (1/8" -27 NPT)

Edelbrock part #3546 for Pro-Flo 3 Fuel Sensor, It includes a 1/8-27 NPT fuel pressure sensor with a -6 AN fuel pressure take-off fitting

Pro-Flo EFI Air Temperature Sensor 3/8"-18 NPT Thread

The Edelbrock #3588 Air Temp Sensor with 3/8"-18 NPT threads.

QTY 4 K-Type Closed Tip Thermocouple

• Comes with everything needed to attach to our CAN EGT Module
• Sold in a set of 4
• Includes K-Type Closed Tip Thermocouple, Inconel sheath, 1/8" NPT compression fitting, 10-foot extension harness

SENSOR; FUEL PRESSURE; 0-100PSI; 1/8in. NPT MALE

• Built In Connector Mates To Delphi Packard Metri-Pack
• 150 Series Connector [12065287-Not Included]

SENSOR; FUEL PRESSURE; 0-15PSI; 1/8in. NPT MALE

• Built In Connector Mates To Delphi Packard Metri-Pack
• 150 Series Connector [12065287-Not Included]

SENSOR KIT; PRESSURE; 100PSI; 8FT. HARNESS; FOR ULTIMATE DL

• Solid-State Data Acquisition Quality Sensor
• Incl. 8 ft. Motorsport Grade Harness