Engine Components

High Energy 7.725" and 8.684" Long, 3/8" Diameter Pushrod Set

High Energy Pushrods from COMP Cams are an affordable, high quality solution when building street rods, RV's and daily drivers.

Replacement Adjusting Nut Set for Magnum Rockers w/ 3/8" Stud

Designed for ultimate strength and locking force High Energy and Magnum polylocks are best for moderate lift and spring pressure Applications Hi-Tech Polylocks work well in all high end Race applications.

Engine Valve Spring Kit

Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application.

Adjustable Timing Control

• Adjust the timing 15° from the driver’s seat!
• Easily connects to your MSD Ignition.

Magnum 7.800" Long, .080" Wall, 5/16" Diameter Pushrod Set

Magnum pushrods from COMP Cams offer an affordable solution for your .080" wall chromemoly Pushrod needs.

Set of 16 O-Ring Valve Seals for Stock Guide Size, 11/32" Valve Stem

Fits: 11/32" Valve Stems / OE-Size Valve Guides (.400" Outer Diameter).

10 Superlock Steel Retainer Set of 16 for 1.500"-1.550" OD Valve Spring

Valve springs with larger diameters require retainers to handle the higher pressures developed by the springs.

7 Steel Retainer Set of 16 for 11/32" Valve w/ 26915/26918 Beehive Springs

Valve springs with larger diameters require retainers to handle the higher pressures developed by the springs.

Set of 16 Metal Viton Valve Seals for .530" Guide Size, 3/8 Valve Stem

3/8 x .530" Metal Body Viton Valve Seal

LS High-Mount A/C Accessory Drive Bracket - Fits Sanden SD508 or SD7 Comp.

• The most cost effective LS bracket solution on the market!
• Utilizes commonly available and affordable GM A/C compressors
• Accepts GM R4 compressor (Sanden version now available)

Stud Girdle Adjusting Nut Set of 12 for 3/8" Stud w/ (4) 4509S Snap Rings

Designed for ultimate strength and locking force High Energy and Magnum polylocks are best for moderate lift and spring pressure Applications Hi-Tech Polylocks work well in all high end Race applications.

Baffled Breather Grommets

• Replaces Stock Grommets
• 2 Per Set
• Fits 1.25 inch valve cover hole.

Set of 16 PTFE Valve Seals for .530" Guide Size, 3/8" Valve Stem

Fits: 3/8" Valve Stems - .530" Guides (.630" Seal Diameter).

0 Degree Retard Module

Zero degree module for use when a module is not used.

10 Lightweight Titanium Retainer Set of 16 for 1.625" OD Triple Springs

Upgrading to these 10& deg

Endure-X Solid Roller Lifter w/ .904" Diameter, Left Pushrod Seat, .300" Taller

.300" Tall Roller lifter, .210" left offset Pushrod seat, cutaway body with oil band, single lifter

Engine Valve Spring Kit

COMP Cams' part number 916-16, valve springs, 1.567" 2-Spring Assembly

Engine Valve Spring Kit

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application.

High Energy 212/212 Hydraulic Flat CL Kit Kit International Harvester 304-392

CL-KIT - Cam and Lifter Kit Includes: Camshaft, Lifters, Assembly Lube, Decals and Instructions.

Hi-Tech 7.800" Long, .080" Wall, 5/16" Diameter Pushrod Set

The Pushrod is one of the most important pieces of the valve train, but all too often it's taken for granted. pushrods not only have to be strong enough to not fail, bend or burn up at the ends, they must also match the frequency of all the rest of the pa parts in the valve train, as well as the rpm at which the engine will be run.

LS Accessory Drive Bracket - Installation Kit for Middle Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets

Valve Spring Shim Kit - 1.437" OD, .645" ID, .015", .030", .060" Thickness

This shim kit contains .015", .030" and .060" thick Valve Spring Shims with 1.437" outside diameter and .645" inside diameter are used to equalize the installed height of valve springs.

Dual Valve Spring with Damper, 1.442 OD, 1.800 IH, .600 Lift, 391 LBS/IN, FT/HR - Set

COMP Cams' new 26987 dual valve springs are a product of innovative design and superior craftsmanship.

Elite Race Dual Valve Springs: 1.551" OD, 2.000 IH, .800 Lift, 502 LBS/IN, SR - Set

COMP Cams' 26097 dual valve springs are a product of innovative design and superior craftsmanship.

Hi-Tech 6.950" Long, .080" Wall, 5/16" Diameter Pushrod

The Pushrod is one of the most important pieces of the valve train, but all too often it's taken for granted. pushrods not only have to be strong enough to not fail, bend or burn up at the ends, they must also match the frequency of all the rest of the pa parts in the valve train, as well as the rpm at which the engine will be run.