Engine Components

High Energy 9.677" Long, 5/16" Diameter Pushrod

High Energy pushrods from COMP Cams are an affordable, high quality solution when building street rods, RV's and daily drivers.

High Vacuum Seal Kit for Belt Drive System

High Vacuum Seal Kit for 6200/6300 Belt Drive System

Hi-Tech 210 Radius 8.600" Long, .080" Wall, 3/8" Diameter Pushrod Set

Designed for high lift Applications where Pushrod and seat interference are problems at maximum lift, Hi-Tech 210& deg

Hi-Tech 7.750" Long, .105" Wall, 5/16" Diameter Pushrod Set of 12

Designed to be 17% stiffer than 0.080" wall pushrods, COMP Hi-Tech .105" pushrods feature the same diameter oil holes as standard to retain full flow.

Hi-Tech 9.400" Long, .080" Wall, 5/16" Diameter Pushrod Set

The Pushrod is one of the most important pieces of the valve train, but all too often it's taken for granted. pushrods not only have to be strong enough to not fail, bend or burn up at the ends, they must also match the frequency of all the rest of the pa parts in the valve train, as well as the rpm at which the engine will be run.

Hi-Tech 9.450" Long, .080" Wall, 3/8" Diameter Pushrod Set

The Pushrod is one of the most important pieces of the valve train, but all too often it's taken for granted. pushrods not only have to be strong enough to not fail, bend or burn up at the ends, they must also match the frequency of all the rest of the pa parts in the valve train, as well as the rpm at which the engine will be run.

Hi-Tech Rocker Stud Set w/ 7/16" Base Thread and 1/2" Rocker Thread

Hi-Tech Rocker Stud Set with 7/16" Base Thread and 1/2" Rocker Thread

HRT Turbo

The HRT Camshaft Series uses the newest and most advanced lobe designs from COMP Cams in order to produce some of the highest average power and torque increases available for turbo and supercharged engines.

Idler Bearing for Hi-Tech Belt Drive Systems

Replacement Idler Bearing for Hi-Techâ„¢ Belt Drive Systems.

Idler Pulley

• Genuine Holley Quality Parts

ID Spring Locator - 1.100" OD, .470" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator - 1.300" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator - 1.540" OD, .640" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator - 1.550" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

Intake Valves for #60379 Cylinder Heads

The Edelbrock #9768 Intake Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

LOWER SEAL,FOR 6502/6506 BELT

Lower Seal for #6502 and #6506 Hi-Tech Belt Drive

Lower Structure Support for Gen III Hemi Engines and Transmissions

• Reduces vibration and noise
• Rigid cast aluminum design with a natural as-cast aluminum finish
• Bolts on over existing oil pan with included fasteners

Low-Mount LS Accessory Drive Bracket - Driver's Side P/S & Alt Bracket Black

• Fits Middle and Long Accessory Spacing
• Installation Kit 21-4 Required w/ Long Spacing
• Cost Effective Solution

LS Accessory Drive Bracket - Installation Kit for Middle Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets

LS/LT High-Mount Accessory Drive Bracket - A/C, P/S & Alt Brackets

• The most cost effective LS bracket solution on the market!
• A/C bracket accepts GM R4 compressor (Sanden version now available)
• Ideal for crate engines, take out motors and engine builders!

Magnum 7.150" Long, .080" Wall, 5/16" Diameter Pushrod Set

Magnum pushrods from COMP Cams offer an affordable solution for your .080" wall chromemoly Pushrod needs.

Magnum 7.400" Long, .080" Wall, 5/16" Diameter Pushrod Set

Magnum pushrods from COMP Cams offer an affordable solution for your .080" wall chromemoly Pushrod needs.

Magnum Polylock for 3/8" Rocker Stud

3/8" Magnum Poly Lock

Magnum Rocker Stud w/ 7/16" Base Thread and 7/16" Rocker Thread

7/16" Magnum Stud

POLY LOCKS, 7/16 HI TECH

7/16 HI Tech Poly Lock-1