Performance Parts

Hose End

• For use w/PowerFlex High PSI PTFE Hose
• Machined from Steel with Endura Finish Nickel Plating

Hose End

• For use w/PowerFlex High PSI PTFE Hose
• Machined from Steel with Endura Finish Nickel Plating

HPS Disc Brake Pad

• Extended Pad Life
• Low Dust
• Virtually Noise-Free

HVAC Filter; 20 x 23 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HydraMat® Install Magnet Kit

• Magnet with integrated mounting stud
• Easy installation
• Includes 4 magnets, nuts and washers

Idle Air Control Motor for Atomic TBI

Atomic TBI and Atomic 2 factory replacement IAC motor, includes gasket O-ring.

Idle Air Control Valve #36017 Hitachi Type

Idle Air Control Valve & Gasket

ID Spring Locator Set of 16 - 1.600" OD, .570" ID, .060" Thickness

Spring seats for #26055 with .570" guide.

ID Spring Locator Set of 16 - 1.635" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

IN-LINE FUEL PULSE DAMPER

• Fittings included for damper/regulator’s and direct mount dampers
• Vacuum fitting and one foot of hose included with all dampers for vacuum referencing
• Assembled and tested in the USA

IN-LINE FUEL PULSE DAMPER

• Fittings included for damper/regulator’s and direct mount dampers
• Vacuum fitting and one foot of hose included with all dampers for vacuum referencing
• Assembled and tested in the USA

IN-LINE FUEL PULSE DAMPER

• Fittings included for damper/regulator’s and direct mount dampers
• Vacuum fitting and one foot of hose included with all dampers for vacuum referencing
• Assembled and tested in the USA

Intake Manifold replacement top gasket

Edelbrock part #6988 replacement top gasket for Edelbrock #7070 intake manifolds are made to our high standards of quality and performance.

Intake Valve for #60779 & #60179 Cylinder Heads

The Edelbrock #9365 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for 77169, 77179, 77189, 77199 & 77359 Heads

The Edelbrock #9370 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Inverted flare fitting 9/16-18 for 1/4 inch line

• Manufactured to OE specifications

Kill Switch for MSD 12 and 20 Amp Pro Mags

The switch is rated at 15 amps so it can handle the power of the Pro-Mag 12.

LED BULB; REPLACEMENT; T1-3/4 WEDGE; RED; FOR MONSTER TACH

• 1.5 Lumen Output
• .02 Amp Draw
• Bulb Life Expectancy 100000 Hours

LED Shift Light

The MSD Shift Light will turn on to "remind" you to shift when the engine reaches your specified rpm.

Line Clamp

• Widest Selection Available

Line Clamp

• Black Anodized
• Fits 1/2 in. Tubing
• Lightweight Aluminum

Liquid Chill Synthetic Engine Coolant, Premixed

• Protects against boil-over to 265 F and freezing to -26 F
• Reduces engine wear and inhibits corrosion
• Portable 64 oz. container

LoadLifter Hose Assembly, 16'

• Limited Warranty 2 Year
• Made In USA
• LoadLIfter Hose Assembly

Lokjaw Locking Ties - 14" 5-Pack

• Locks down securely to prevent loosening, slipping, or failure
• Ideal for high-heat, high-vibration environments
• Constructed from high-grade 316 stainless steel

LS High-Mount A/C Accessory Drive Bracket - Passenger's Side A/C Bracket

• The most cost effective LS bracket solution on the market!
• Utilizes commonly available and affordable GM A/C compressors
• Accepts GM R4 compressor (Sanden version now available)