Performance Parts

Hose Clamp

• Rubber Covered Hose Loop
• Spring Steel Tab Mount

Hose End

• For use w/PowerFlex High PSI PTFE Hose
• Machined from Steel with Endura Finish Nickel Plating

HP Plus Disc Brake Pad

• HP Plus Compound
• Wide Temperature Range
• Fade Resistant

HPS 5.0 Disc Brake Pad

• Improved Pedal Feel
• Gentle On Rotors
• Extended Pad Life

HPS Disc Brake Pad

• Extended Pad Life
• Low Dust
• Virtually Noise-Free

HVAC Filter; 14 x 18 x 1, Merv 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC Filter; 14 x 24 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC Filter; 18 x 20 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC Filter; 18 x 30 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC Filter; 20 x 22 x 1, MERV 8

• Lifetime limited warranty
• Merv 8 rating
• Easy to clean and reuse

HVAC Filter; 20 x 23 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC Filter; 24 x 24 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HydraMat® Install Magnet Kit

• Magnet with integrated mounting stud
• Easy installation
• Kit includes 4 magnets, nuts and washers

Idler Pulley - Holley Accessory Drive

• Genuine Holley Quality Parts

ID Spring Locator Set of 16 - 1.600" OD, .570" ID, .060" Thickness

Spring seats for #26055 with .570" guide.

ID Spring Locator Set of 16 - 1.635" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

Ignition Brass Open Barrel Kit Terminal kit (326pcs). Contains Ring and Spade terminals; Female and Male Bullet Connectors; for 22-12 AWG wire;PVC covers for terminals;

• 326 Piece Kit
• Insulation Material: PVC Clear
• Wire sizes from 12 - 22 AWG

Ignition Connector kit (150pcs). Contains #6 spade terminals, Butt connector, #6&#8 ring terminals,Female and Male disconnectors for 22-14 AWG wire

• 150 Piece Kit
• Material for Ring and Spde Terminals: Tin Plated Copper
• Wire sizes from 14 - 22 AWG

Ignition Dual Wall Heat Shrink Tube Kit 106 pcs. Contains, Red and Black sleeves tube sizes from 1/8" up to 1/2" in 3" Lengths. Made of Polyolefin, Waterproof, Shrink Ratio 3:1, Rated up to 600V, and Temp. rated at -49° to 257°F

• 106 Piece Dual Wall Shrink Tube (waterproof)
• Tube Sizes from 1/8" to 1"
• Material: Polyolefin (Red and Black)

Ignition Weather Pack connector kit 209 pcs. Contains 1,2,3,4, and 6 pole Receptacles; Pins and Seals for 24-10 AWG wire; and a weather pack terminal release tool

• 209 Piece Kit
• Connector has locking mechanism that align terminal and seal
• Temperature rated at -40° C to 120° C (-40° to 248° F)

IN-LINE FUEL PULSE DAMPER

• Fittings included for damper/regulator’s and direct mount dampers
• Vacuum fitting and one foot of hose included with all dampers for vacuum referencing
• Assembled and tested in the USA

In-Line RGB Link

• Increases the load capability and extends the signal of any universal RGB controller.

Inner Bearing Race; 3;500-lb. Axles; 8 Pack

• Compatible With 3500 lbs Axles
• Pairs With Bearing No.L68149
• Easy DIY Installation; Includes Eight Inner Races

Intake Valve for 60459, 60479, 60499 & 60559 Heads

The Edelbrock #9770 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for #60929 & #60189 Cylinder Heads

The Edelbrock #9640 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.