Performance Parts

HVAC Filter; 14 x 18 x 1, MERV 11

• Lifetime limited warranty
• Merv 11 rating
• Easy to clean and reuse

HVAC FILTER; 24 X 30 X 1, MERV 11

• Merv 11 rating
• Easy to clean and reuse
• Lifetime limited warranty

Ignition Solder and Heat seal splice kit. Contains white, red, blue, and yellow for 26-10 AWG. Waterproof, Crimpless, 2:1 shrinkage ratio, Rated up to 600V, Temp. range from -67° to 220° F.

• 40 Piece Kit
• Temperature rated at -40° C to 105° C (-40° to 221° F)
• Starting Temperature of Soldering Melt: 115° C (239° F)

In-Line LED RGB Controller

• Modes include: Breathing Mode, Heartbeat Mode, Primary and Secondary Strobe Modes, Control Dimming Mode

Inner Bearing Race; 10;000-lb. Axles; 6 Pack

• Compatible With 10000 lbs Axles
• Pairs With Bearing No.387A
• Easy DIY Installation; Includes Six Inner Races

Inverted flare fitting 9/16-18 for 3/16 inch line

• Manufactured to OE specifications

Inverted flare plug 3/8-24

• Manufactured to OE specifications

Lifter Valley Standpipe - Set of 8

These standpipes help maintain a healthy oil level in the valley of your Small Block Chevrolet.

LINE ADAPTR-MNFLD FOR SD7 A/C COMP

• Manifold adapter allows connection to custom A/C lines

LINE; BRAIDED STAINLESS STEEL; #3 DIA.; 4FT. LENGTH;-3AN AND 1/8in. NPTF FITTING

• For Mechanical Pressure Gauge
• 4 ft. Hose Length
• Operating Temp -65 to 450 Deg. F

LINE; BRAIDED STAINLESS STEEL; #4 DIA.; 6FT. LENGTH;-4AN AND 1/8in. NPTF FITTING

• For Mechanical Pressure Gauge
• 6 ft. Hose Length
• 12000 PSI Burst Pressure

Line Clamp

• Widest Selection Available

Line Clamp

• Widest Selection Available

Line Clamp

• The Fasteners have 8-32 threads and are 3/4" Long

LS Accessory Drive Bracket - Installation Kit for Long Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets

LS/LT High-Mount Accessory Drive Bracket - Driver's Side P/S & Alt Bracket

• The most cost effective LS bracket solution on the market!
• Utilizes commonly available and affordable GM alternators and power steering pumps
• Ideal for crate engines, take out motors and engine builders!

M 9100 (Bump Stop) - Suspension Bump Stop

• Filled with technology perfected over 3 decades of off-road dominance
• Monotube gas pressure design maximizes heat dissipation
• Available for lifted truck, custom truck, rock crawling and off-road racing applications

M 9100 (Bump Stop) - Suspension Bump Stop

• Filled with technology perfected over 3 decades of off-road dominance
• Monotube gas pressure design maximizes heat dissipation
• Available for lifted truck, custom truck, rock crawling and off-road racing applications

Machined Steel 7 Degree, 8mm, Single Groove Race Lock

Machined Steel 7 Degree, 8mm, Single Groove Race Lock - Single

Machined Steel Set of 16 - 7 Degree, 5/16", Single Groove Race Locks

Includes 16 Pairs of Machined Steel Race Locks: 1 Groove, 7& deg

Magnetic Pickup Assembly

This is a replacement pickup for older style crank trigger systems that require a magnetic pickup.

Magnet Sleeve (only) for 2161 Ignitor Kit

• Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
• Replacement Magnet Sleeve for PerTronix 2161 (Service Part Only)
• Rotating cobalt magnets trigger a Hall Effect integrated circuit; no points to burn; no moving parts to wear out.

Magnum Polylock Set for 3/8" Rocker Stud

Designed for ultimate strength and locking force High Energy and Magnum polylocks are best for moderate lift and spring pressure Applications Hi-Tech Polylocks work well in all high end Race applications.

MAP Sensor 3-bar for blown/turbo applications

• Applications up to 30lbs of boost.

Marine Flame Arrestor

• Marine approved per SAE J1928 standard
• Smoothes and straightens incoming air
• Washable and reusable