Performance Parts

Hydraulic Release Bearing Kit

• Compatible With Dot 3 And Dot 4 Brake Fluids
• Utilizes OEM (Original Equipment) Connection Point For Easy Installation
• Commonly Used For Transmission Swap Projects

ID Spring Locator - 1.285" OD, .532" ID, .040" Thickness

ID Spring Locator - 1.285" OD, .525" ID, .040" Thickness

ID Spring Locator - 1.285" OD, .805" ID, .135" Thickness

ID Spring Locator - 1.285" OD, .805" ID, .135" Thickness - Single

ID Spring Locator Set of 100 - 1.510" OD, .570" ID, .060" Thick

The older style standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

ID Spring Locator Set of 16 - 1.350" OD, .515" ID, .050" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

Ignition Solder and Heat seal splice kit. Contains white, red, blue, and yellow for 26-10 AWG. Waterproof, Crimpless, 2:1 shrinkage ratio, Rated up to 600V, Temp. range from -67° to 220° F.

• 40 Piece Kit
• Temperature rated at -40° C to 105° C (-40° to 221° F)
• Starting Temperature of Soldering Melt: 115° C (239° F)

Ignition Weather Pack connector kit 209 pcs. Contains 1,2,3,4, and 6 pole Receptacles; Pins and Seals for 24-10 AWG wire; and a weather pack terminal release tool

• 209 Piece Kit
• Connector has locking mechanism that align terminal and seal
• Temperature rated at -40° C to 120° C (-40° to 248° F)

INFRA RED EXTERNAL PRINTER; 12V

• Uses Standard 58mm Thermal Paper
• Incl. AC Power Adapter And 110V Cigar Lighter Power Adapter
• 6 in. x 4.5 in. x 3.5 in.

In-Line LED RGB Controller

• Modes include: Breathing Mode, Heartbeat Mode, Primary and Secondary Strobe Modes, Control Dimming Mode

In-Line RGB Link

• Increases the load capability and extends the signal of any universal RGB controller.

Inner Bearing Cone; 10;000-lb. Axles; 6 Pack

• Compatible With 10000 lbs Axles
• Pairs With Bearing Race No.382A
• Compatible With Most Competitor Trailer Axle Hubs

Intake Valves for #60979 Cylinder Heads

The Edelbrock #9779 Intake Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Inverted flare plug 3/8-24

• Manufactured to OE specifications

Jet Assortment Kit

Jet Assortment Kit with billet plate.

LED BULB; REPLACEMENT; T3 WEDGE; AMBER

• 9.8-11 Lumen Output
• .06 Amp Draw
• Bulb Life Expectancy 100000 Hours

Lifter Valley Standpipe - Set of 8

These standpipes help maintain a healthy oil level in the valley of your Small Block Chevrolet.

LINE; BRAIDED STAINLESS STEEL; #4 DIA.; 6FT. LENGTH;-4AN AND 1/8in. NPTF FITTING

• For Mechanical Pressure Gauge
• 6 ft. Hose Length
• 12000 PSI Burst Pressure

Line Clamp

• The Fasteners have 8-32 threads and are 3/4" Long

LOWER SEAL,FOR 6502/6506 BELT

Lower Seal for #6502 and #6506 Hi-Tech Belt Drive

Lower Structure Support for Gen III Hemi Engines and Transmissions

• Reduces vibration and noise
• Rigid cast aluminum design with a natural as-cast aluminum finish
• Bolts on over existing oil pan with included fasteners

LS Accessory Drive Bracket - Installation Kit for Long Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets

LS COOLING MANIFOLD RAW

• Genuine Holley Quality Parts

LS COOLING MANIFOLD RAW A/C Delete

• Genuine Holley Quality Parts

LS/LT High-Mount Accessory Drive Bracket - Driver's Side P/S & Alt Bracket

• The most cost effective LS bracket solution on the market!
• Utilizes commonly available and affordable GM alternators and power steering pumps
• Ideal for crate engines, take out motors and engine builders!

LT COOLING MANIFOLD RAW-A/C and P/S Delete

• Genuine Holley Quality Parts