Performance Parts

Hi-Tech One-Piece 8.050" Long, .135" Wall, 3/8" Diameter Pushrod

With a massive 37 percent increase in stiffness over standard .080" wall Pushrods, Hi-Tech 210& deg

Hi-Tech Polylock Set for 3/8" Stud Ultra Pro Magnum Rockers

Designed for ultimate strength and locking force High Energy and Magnum polylocks are best for moderate lift and spring pressure Applications Hi-Tech Polylocks work well in all high end Race applications.

Hold-Down, Coil Wire

The MSD Coil Wire Retainer holds the boot securely in the coil.

Hose Clamp

• Rubber Covered Hose Loop
• Spring Steel Tab Mount

Hose End

• For use w/PowerFlex High PSI PTFE Hose
• Machined from Steel with Endura Finish Nickel Plating

Hose Separator

• 6061-T6 Aluminum
• Black Anodized
• Fits 8 AN ProClassic Hose

Hose & Tubing Separator

• For Professional Engine Look

Hose & Tubing Separator

• For Professional Engine Look

HVAC FILTER; 10 X 20 X 1, MERV 11

• Merv 11 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC Filter; 12 x 12 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC FILTER; 20 X 25 X 1, MERV 11

• Merv 11 rating
• Easy to clean and reuse
• Lifetime limited warranty

HVAC FILTER; 24 X 30 X 1, MERV 11

• Merv 11 rating
• Easy to clean and reuse
• Lifetime limited warranty

Ignition Solder and Heat seal splice kit. Contains white, red, blue, and yellow for 26-10 AWG. Waterproof, Crimpless, 2:1 shrinkage ratio, Rated up to 600V, Temp. range from -67° to 220° F.

• 40 Piece Kit
• Temperature rated at -40° C to 105° C (-40° to 221° F)
• Starting Temperature of Soldering Melt: 115° C (239° F)

Inverted flare fitting 9/16-18 for 3/16 inch line

• Manufactured to OE specifications

Inverted flare plug 3/8-24

• Manufactured to OE specifications

Lifter Valley Standpipe - Set of 8

These standpipes help maintain a healthy oil level in the valley of your Small Block Chevrolet.

LINE ADAPTR-MNFLD FOR SD7 A/C COMP

• Manifold adapter allows connection to custom A/C lines

LINE; BRAIDED STAINLESS STEEL; #3 DIA.; 4FT. LENGTH;-3AN AND 1/8in. NPTF FITTING

• For Mechanical Pressure Gauge
• 4 ft. Hose Length
• Operating Temp -65 to 450 Deg. F

LINE; BRAIDED STAINLESS STEEL; #4 DIA.; 6FT. LENGTH;-4AN AND 1/8in. NPTF FITTING

• For Mechanical Pressure Gauge
• 6 ft. Hose Length
• 12000 PSI Burst Pressure

Line Clamp

• Widest Selection Available

Line Clamp

• Widest Selection Available

Line Clamp

• The Fasteners have 8-32 threads and are 3/4" Long

LS Accessory Drive Bracket - Installation Kit for Long Alignment

• Aluminum construction
• Will not rust
• Lighter than steel brackets

LS/LT High-Mount Accessory Drive Bracket - Driver's Side P/S & Alt Bracket

• The most cost effective LS bracket solution on the market!
• Utilizes commonly available and affordable GM alternators and power steering pumps
• Ideal for crate engines, take out motors and engine builders!

M 9100 (Bump Stop) - Suspension Bump Stop

• Filled with technology perfected over 3 decades of off-road dominance
• Monotube gas pressure design maximizes heat dissipation
• Available for lifted truck, custom truck, rock crawling and off-road racing applications