Performance Parts

HVAC Filter; 24 x 24 x 1, MERV 8

• Merv 8 rating
• Easy to clean and reuse
• Lifetime limited warranty

HydraMat® Install Magnet Kit

• Magnet with integrated mounting stud
• Easy installation
• Kit includes 4 magnets, nuts and washers

Idle Air Control Motor for Atomic TBI

Atomic TBI and Atomic 2 factory replacement IAC motor, includes gasket O-ring.

Idler Pulley - Holley Accessory Drive

• Genuine Holley Quality Parts

ID Spring Locator Set of 16 - 1.285" OD, .532" ID, .135" Thickness

ID Spring Locator Set of 16 - 1.300" OD, .510" ID, .060" Thickness

ID Spring Locator Set of 16 - 1.450" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.510" OD, .570" ID, .060" Thickness

Lower Seat for 26120 with .570 Guide

ID Spring Locator Set of 16 - 1.540" OD, .640" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.550" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.550" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.635" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.655" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

Ignition Heat shrink Terminal kit (165pcs). Contains Ring and Spade terminals; Butt connectors; Female and Male disconnects;Closed end connectors for 22-10 AWG wire(Red,Blue,Yellow).3:1 shrinkage ratio;

• 165 Piece Kit
• Polyethylene insulation (PE) with Copper Terminal Material
• Wire sizes from 10 - 22 AWG

Ignition Primary Wire Extension Kit

• Primary Wire Extension Kit can be used to increase the wire length of our point conversion kits or distributors.
• Kit includes 39" of our quality 20 guage silicone jacketed red and black wire, ring terminals, quick disconnect…

Ignition Wire Marker 8 mm

• Fits 8mm diameter wire

IN-LINE FUEL PULSE DAMPER

• Fittings included for damper/regulator’s and direct mount dampers
• Vacuum fitting and one foot of hose included with all dampers for vacuum referencing
• Assembled and tested in the USA

Inner Bearing Race; 3;500-lb. Axles; 8 Pack

• Compatible With 3500 lbs Axles
• Pairs With Bearing No.L68149
• Easy DIY Installation; Includes Eight Inner Races

Intake Valve for 60459, 60479, 60499 & 60559 Heads

The Edelbrock #9770 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for #60779 & #60179 Cylinder Heads

The Edelbrock #9365 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for #60929 & #60189 Cylinder Heads

The Edelbrock #9640 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for #77619, #77629, #77639 & #77649 Heads

The Edelbrock #9784 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for #77919, #77929, #77939 & #77949 Heads

The Edelbrock #93774 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valves for #60459, #60479, #60499 & #60559 Heads

The Edelbrock #9775 Intake Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

LINE; BRAIDED STAINLESS STEEL; #3 DIA.; 6FT. LENGTH;-3AN AND 1/8in. NPTF FITTING

• 4 ft. Hose Length
• 12000 PSI Burst Pressure
• Incl. 3AN Female Straight