Performance Parts

ID Spring Locator Set of 100 - 1.300" OD, .510" ID, .060" Thick

The older style standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

ID Spring Locator Set of 100 - 1.500" OD, .570" ID, .060" Thick

The older style standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

ID Spring Locator Set of 100 - 1.540" OD, .640" ID, .060" Thick

The older style standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

ID Spring Locator Set of 100 - 1.540" OD, .640" ID, .060" Thick

The older style standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

ID Spring Locator Set of 100 - 1.550" OD, .570" ID, .060" Thick

The older style standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

ID Spring Locator Set of 100 - 1.550" OD, .570" ID, .060" Thick

The older style standard shims will not hold up to the extreme spring pressures and high RPM found in racing engines being built today.

ID Spring Locator Set of 16 - 1.300" OD, .505" ID, .040" Thickness

Complete Set of (16) ID Spring Locators.

ID Spring Locator Set of 16 - 1.340" OD, .570" ID, .100" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

ID Spring Locator Set of 16 - 1.540" OD, .570" ID, .060" Thickness

Ignition Heat shrink Terminal kit (165pcs). Contains Ring and Spade terminals; Butt connectors; Female and Male disconnects;Closed end connectors for 22-10 AWG wire(Red,Blue,Yellow).3:1 shrinkage ratio;

• 165 Piece Kit
• Polyethylene insulation (PE) with Copper Terminal Material
• Wire sizes from 10 - 22 AWG

Ignition Primary Wire Extension Kit

• Primary Wire Extension Kit can be used to increase the wire length of our point conversion kits or distributors.
• Kit includes 39" of our quality 20 guage silicone jacketed red and black wire, ring terminals, quick disconnect…

Ignition Wire Marker 8 mm

• Fits 8mm diameter wire

Indicator Gauge Pointer Upgrade

Quality, Service and Value are not new to us.

Inner Bearing Cone-5;200 to 8;000-lb. Axles

• Comes With Nylon Bushings
• Industry Reference EQ-E1

Inner Bearing Race; 3;500-lb. Axles; 8 Pack

• Compatible With 3500 lbs Axles
• Pairs With Bearing No.L68149
• Easy DIY Installation; Includes Eight Inner Races

Inspection Cover

• Black Oxide Steel
• Included with LK4000K
• Hardware included

Installation Kit for GM Gen V LT Accessory Drive

• No engine modification required - completely bolt-on
• Cost Effective and Proven Solution
• Utilizes conventional single sided belt

Intake Manifold Spacer

• Cast Aluminum
• Dominator To Square Bore
• 2 1/4" Height

Intake Valve for #60669 & #60689 Cylinder Heads

The Edelbrock #93661 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valves for #60579, #61579 & #61599 Cylinder Heads

The Edelbrock #9780 Intake Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valves for #60809 & #60819 Cylinder Heads

The Edelbrock #93781 Intake Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valves for #77619, #77629, #77639 & #77649 Heads

The Edelbrock #9785 Intake Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valves for #77919, #77929, #77939 & #77949 Heads

The Edelbrock #93775 Intakes Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Inverted flare fitting 3/8-24 for 3/16 inch line

• Manufactured to OE specifications

Inverted flare line fitting - 1/2-20 for 3/16 inch line

• Manufactured to OE specifications