Performance Parts

In-Line LED RGB Controller

• Modes include: Breathing Mode, Heartbeat Mode, Primary and Secondary Strobe Modes, Control Dimming Mode

In-Line RGB Link

• Increases the load capability and extends the signal of any universal RGB controller.

Inner Bearing Cone; 10;000-lb. Axles; 6 Pack

• Compatible With 10000 lbs Axles
• Pairs With Bearing Race No.382A
• Compatible With Most Competitor Trailer Axle Hubs

Intake Valves for #60979 Cylinder Heads

The Edelbrock #9779 Intake Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Jet Assortment Kit

Jet Assortment Kit with billet plate.

LED BULB; REPLACEMENT; T3 WEDGE; AMBER

• 9.8-11 Lumen Output
• .06 Amp Draw
• Bulb Life Expectancy 100000 Hours

LOWER SEAL,FOR 6502/6506 BELT

Lower Seal for #6502 and #6506 Hi-Tech Belt Drive

Lower Structure Support for Gen III Hemi Engines and Transmissions

• Reduces vibration and noise
• Rigid cast aluminum design with a natural as-cast aluminum finish
• Bolts on over existing oil pan with included fasteners

LS COOLING MANIFOLD RAW

• Genuine Holley Quality Parts

LS COOLING MANIFOLD RAW A/C Delete

• Genuine Holley Quality Parts

LS/LT High-Mount Accessory Drive Bracket - Driver's Side P/S & Alt Bracket

• The most cost effective LS bracket solution on the market!
• Utilizes commonly available and affordable GM alternators and power steering pumps
• Ideal for crate engines, take out motors and engine builders!

LT COOLING MANIFOLD RAW-A/C and P/S Delete

• Genuine Holley Quality Parts

Machined Steel 7 Degree, 8mm, Single Groove Race Lock

Machined Steel 7 Degree, 8mm, Single Groove Race Lock - Single

Machined Steel Set of 100 - 7 Degree, 11/32", Single Groove Race Locks

Most people believe that the tang inside a valve lock holds the retainer and valve spring in place while the engine is running, but this isn't the case.

Machined Steel Set of 12 - 7 Degree, 11/32", Single Groove Race Locks

Includes 12 Pairs of Machined Steel Race Locks: 1 Groove, 7& deg

Magnet Sleeve (only) for 1144A Ignitor Kit

• Replacement Magnet Sleeve for PerTronix 1144A (Service Part Only)

Magnet Sleeve (only) for 1247 Ignitor Kit

• Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
• Replacement Magnet Sleeve for PerTronix 1247 (Service Part Only)
• Rotating cobalt magnets trigger a Hall Effect integrated circuit; no points to burn; no moving parts to wear out.

Magnet Sleeve (only) for 1441A Ignitor Kit

• Replacement Magnet Sleeve for PerTronix 1441A (Service Part Only)
• Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
• Rotating cobalt magnets trigger a Hall Effect integrated circuit; no points to burn; no moving parts to wear out.

Magnet Sleeve (only) for 1542 Ignitor Kit

• Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
• Replacement Magnet Sleeve for PerTronix 1542 (Service Part Only)
• Rotating cobalt magnets trigger a Hall Effect integrated circuit; no points to burn; no moving parts to wear out.

Magnet Sleeve (only) for 2842 Ignitor Kit

• Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
• Replacement Magnet Sleeve for PerTronix 2842 (Service Part Only)
• Rotating cobalt magnets trigger a Hall Effect integrated circuit; no points to burn; no moving parts to wear out.

Magnum 8.600" Long, .080" Wall, 5/16" Diameter Pushrod

Magnum pushrods from COMP Cams offer an affordable solution for your .080" wall chromemoly Pushrod needs.

Manifold Fitting

• Brass
• Made In The USA
• Sold Individually

MAP Sensor Assembly for Atomic TBI

Atomic TBI factory replacement MAP sensor.

Max-Cool Transmission Cooler Kit for Dodge 8HP70 2015 & up Challengers/Chargers

The TCI® Max-Cool Transmission Cooler Kit addresses overheating issues sometimes seen in the 8HP70 eight-speed automatic transmission installed in 2015 and newer Challengers and Chargers.

Max-Fire Ignition HEI Coil-In-Cap in Black Finish

Edelbrock part #22743 HEI Coil-In-Cap, design is for use with GM HEI coil in-cap distributors with red and yellow primary wires.