Engine Components

1 Umbrella Valve Seal for Stock Guide Size, 11/32" Valve Stem

< ul>< li> Fits: 11/32" Valve Stems - OE-Size Valve Guides (.750" Outer Diameter)</li>< li> Valves Seals keep unwanted oil from entering the combustion chamber through clearance in the valve guides</li>< li> Normally used when a larger-than-stock diameter spring is used</li>< li> Requires no machining.

7 Degree Titanium Retainer for 7245 Dual Conical Spring

Upgrading to COMP Cams titanium valve spring retainers will often allow you to gain speed and power because titanium retainers are lighter and as strong as than most Steel ones.

7 Degree Tool Steel Retainer for 8mm Valve, Spring w/ 1.290" O.D

These new Tool Steel Retainers from COMP Cams have a 7& deg

7 Steel Retainer for 11/32" Valve w/ 1.437"-1.500" Spring

Valve springs with larger diameters require retainers to handle the higher pressures developed by the springs.

7 Steel Retainer for 11/32" Valve w/ 26915/26918 Beehive Springs

Valve springs with larger diameters require retainers to handle the higher pressures developed by the springs.

7 Steel Retainer Set of 16 for for 11/32 Valve w/ 26925 Spring

Valve springs with larger diameters require retainers to handle the higher pressures developed by the springs.

7 Titanium Retainer Set of 16 for 26921 Spring w/ 8mm Valve Stem

Upgrading to these 7& deg

BELT GUARD, FRONT, FOR 6100 LO

Front Belt Guard for #6100 Magnum Belt Drive System

BELT GUARD, REAR, FOR 6100 LOW

Lower Gear Rear Belt Guard for #6100 Magnum Belt Drive System

BULK, DUAL SPRINGS W/ DAMPER, 1.442 OD, 1.800 IH, .600 LIFT, 391 LBS/IN, FT/HR

Connecting Rod Vise - Billet Aluminum

• Overall Height: 10"
• Overall Width: 7"
• Depth: 2"

Cork Gasket Material - 1/8 x 12 x 36 Inch

• Ideal for use to make valve cover gaskets, and intake manifold end seals
• 1/8" x 12" x 36"
• Use w/ Oil

Digital Multi-Retard

• Magnetic pick-up compensation circuit
• Adjustable start retard
• Four stages of retard

DUAL SPRING W/ DAMPER, 1.442 OD, 1.800 IH, .600 LIFT, 391 LBS/IN, FT/HR

Dual Taper 7.450" Long, .165" Wall, 7/16" Diameter Pushrod

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 7.500" Long, .165" Wall, 7/16" Diameter Pushrod

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 7.550" Long, .165" Wall, 7/16" Diameter Pushrod Set

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 7.750" Long, .165" Wall, 7/16" Diameter Pushrod Set

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 7.900" Long, .165" Wall, 7/16" Diameter Pushrod Set

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 7.950" Long, .165" Wall, 7/16" Diameter Pushrod

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 7.950" Long, .165" Wall, 7/16" Diameter Pushrod Set

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 8.100" Long, .165" Wall, 7/16" Diameter Pushrod

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 8.200" Long, .165" Wall, 7/16" Diameter Pushrod Set

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 8.250" Long, .165" Wall, 7/16" Diameter Pushrod

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.

Dual Taper 8.300" Long, .165" Wall, 7/16" Diameter Pushrod

Dual Taper 7/16", .165" Wall pushrods from COMP Cams are designed with the middle of the Pushrod being larger in diameter than the two ends.