Engine Components

Exhaust Valve for #60459, 60479, 60499, 60559 & 60439 Heads

The Edelbrock #9771 Exhaust Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Exhaust Valve for #60929 & #60189 Cylinder Heads

The Edelbrock #9642 Exhaust Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Exhaust Valves for #60929 & #60189 Cylinder Heads

The Edelbrock #9643 Exhaust Valves are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

High Energy 8.280" Long, 3/8" Diameter Pushrod

High Energy pushrods from COMP Cams are an affordable, high quality solution when building street rods, RV's and daily drivers.

High Energy 8.500" Long, 5/16" Diameter Pushrod Set

High Energy Pushrods from COMP Cams are an affordable, high quality solution when building street rods, RV's and daily drivers.

High Energy Polylock Set for 3/8" Rocker Stud

Designed for ultimate strength and locking force High Energy and Magnum polylocks are best for moderate lift and spring pressure Applications Hi-Tech Polylocks work well in all high end Race applications.

Hi-Tech 8.050" Long, .080" Wall, 5/16" Diameter Pushrod Set

The Pushrod is one of the most important pieces of the valve train, but all too often it's taken for granted. pushrods not only have to be strong enough to not fail, bend or burn up at the ends, they must also match the frequency of all the rest of the pa parts in the valve train, as well as the rpm at which the engine will be run.

ID Spring Locator Set of 16 - 1.600" OD, .570" ID, .060" Thickness

Spring seats for #26055 with .570" guide.

ID Spring Locator Set of 16 - 1.635" OD, .570" ID, .060" Thickness

The old standard shims will not hold up to the extreme spring pressures and high RPM in today's race engines.

Intake Manifold replacement top gasket

Edelbrock part #6988 replacement top gasket for Edelbrock #7070 intake manifolds are made to our high standards of quality and performance.

Intake Valve for #60929 & #60189 Cylinder Heads

The Edelbrock #9640 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Intake Valve for 77169, 77179, 77189, 77199 & 77359 Heads

The Edelbrock #9370 Intake Valve are 1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow.

Machined Steel 7 Degree, 3/8", Single Groove Race Lock

This single groove Machined Steel Street Lock with 7& deg

Magnum 9.130" Long, .080" Wall, 5/16" Diameter Pushrod

Magnum pushrods from COMP Cams offer an affordable solution for your .080" wall chromemoly Pushrod needs.

Magnum 9.250" Long, .080" Wall, 3/8" Diameter Pushrod Set of 8

Magnum pushrods from COMP Cams offer an affordable solution for your .080" wall chromemoly Pushrod needs.

Magnum Rocker Stud Set w/ 7/16" Base Thread and 7/16" Rocker Thread

COMP Cams takes pride in having the finest Rocker arm Studs available on the market.

Performance Exhaust Gasket Material

• Withstands Extreme Exhaust Heat
• Superior Tensile Strength
• Resists Deteriorating

Performance Exhaust Gasket Material

• Heavy duty material, .062" thick
• Up to 1200 degrees F
• Excellent sealing and durability

Performance Intake Gasket Material

• Conforms well to irregular flange surfaces
• Very good crush resistance at high flange pressures
• Bulk sheet easily cut for making custom gaskets

Race Sportsman 1.332" OD Conical Springs; 1.900" Installed Height; 16 Springs

Revolutionary Advancement In High Performance Spring Technology. < table border="1">< tbody>< tr>< td>7230-16</td>< td> Outer Diameter and</td>< td> Inner Diameter and</td>< td> Seat Load</td>< td> Open Load</td>< td> Coil Bind</td>< td> Rate and</td></tr>< tr>< td> Top</td>< td>1.060"</td>< td>.660"</td>< td rowspan="2"> 145 @ 1.900"</td>< td rowspan="2"> 495 @ 1.225"</td>< td rowspan="2">1.185"</td>< td rowspan="2">520</td></tr>< tr>< td> Bottom</td>< td>1.332"</td>< td>.932"</td></tr></tbody></table>

Race Sportsman 1.454" OD Beehive Springs; 1.800" Installed Height; 16 Springs

COMP Cams Beehive Valve Springs deliver increased valve train stability and a much lighter valve train.

Race Sportsman 1.585" OD Beehive Springs; 1.925" Installed Height; 16 Springs

With a .640" maximum lift, these Beehive Valve Springs were designed for high end Solid flat tappet and hydraulic Roller cams.

Race Street 1.290" OD Conical Springs; 1.800" Installed Height; 16 Springs

Revolutionary Advancement In High Performance Spring Technology. < table border="1">< tbody>< tr>< td>7228-16</td>< td> Outer Diameter and</td>< td> Inner Diameter and</td>< td> Seat Load</td>< td> Open Load</td>< td> Coil Bind</td>< td> Rate and</td></tr>< tr>< td> Top</td>< td>1.020"</td>< td>.650"</td>< td rowspan="2"> 136 @ 1.800"</td>< td rowspan="2"> 412 @ 1.170"</td>< td rowspan="2">1.125"</td>< td rowspan="2">438</td></tr>< tr>< td> Bottom</td>< td>1.290"</td>< td>.920"</td></tr></tbody></table>

Race Street 1.320" OD Dual Springs; 1.770" Installed Height; 16 Springs

Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application.

Race Street 1.320" OD Dual Springs; 1.835" Installed Height; 16 Springs

COMP Cams Dual Valve Springs for street/strip Applications are manufactured from Super Clean® wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter the application.