Batteries & Charging

SPE-29681 Wire Loom

• 3/8 inch inside diameter by 8 feet long
• Made from black polyethylene
• Pre-split for easy installation

Split Wiring Loom

• Includes (6) 4˝ length tie straps
• Slit for easy wire insertion and removal
• Provides neat, clean and organized appearance

Stand Alone Solid State Relay- Black

• Activate with power or ground
• Multiple mounting options
• Diagnostic LED’s

STARTING/CHARGING SYSTEM ANALYZER

• Tests 6 And 12 Volt Batteries
• 20 in.-16 Gauge Test Leads
• LCD Backlit Screen

Stator - Unmolded - Harley Davidson - 22 Amp - 91-98 Sportster

• Covered by our limited 90 Day warranty

Terminal Strip

The MSD Terminal Strip can be used for virtually any wiring installation to pro­vide a clean, professional appearance.

Universal Mounting Bracket - For Voltage Regulator

ACCEL Motorcycle universal mounting bracket lets you install electronic regulators on early model bikes and custom frames for improved charging performance.

14-Amp Turn Signal Flasher (2-3 Lamps; 2-6 Hazards)

• Operates 2-3 Lamps Or 4-6 Hazards
• For Applications Where Over-Current Protection Is Required
• Turn Signal Flashers Are 12-Volt 2-Terminal Flashers

20 Amp Relay Wiring Kit

• 20-Amp relay
• 30 Amp Relay
• Red Butt Connectors

30-AMP IGNITION POWER RELAY. PROVIDES CONSISTENT FULL BATTERY VOLTAGE

• Easy to follow instructions make installation simple
• Small size… Keep your engine bay looking stock
• Universal design… Works with most battery ignition systems

500A Dual Channel Analog Current Sensor

• Good accuracy for high and low current.
• The inner diameter is 21.55mm.
• Operating Temperature Range of -40 to 257 Fahrenheit.

Battery Box Aluminum Nhra Optima Battery

• Hard mounts battery to the frame with 3/8" supplied bolts
• Heavy duty one-piece welded batter hold down and mounting hardware included.
• Complies with NHRA rules

Battery Box Alum Nhra With 2Ga Cables

• Hard mounts battery to the frame with 3/8" supplied bolts
• Heavy duty one-piece welded batter hold down and mounting hardware included.
• Complies with NHRA rules

Battery Relocator Kit-1Ga Single Trunk

• 16' red 2 gauge cable , battery to starter
• 20" black 2 gauge cable, battery to ground
• 13" x 7.25" heavy gauge coated steel tray

Battery Terminal Covers Red Black

• 4-6 gauge
• Pair - 1 red, 1 black
• Top Post

BMS - Plug & Pin Kit

• Kit designed for AEM BMS units
• Waterproof connectors
• Quick-connect connectors

Chrome Alternator Fan & Pulley - Chrome

These Mr.

Female Pins and Seals

Female pins and seals for use with Weathertight Connectors.

Fire Sleeve & Tape Kit 0.625" ID x 36" 010472

• 5/8 in. x 3 ft Length Of Fire Sleeve
• Includes 16 In. Length Of Fire Tape
• Burn Protection During Under Hood Repairs And Maintenance

Fire Sleeve & Tape Kit 1" ID x 36" 010474

• 1 in. x 3 ft Length Of Fire Sleeve
• Includes 16 In. Length Of Fire Tape
• Burn Protection During Under Hood Repairs And Maintenance

Hi-Temp Shrink Tubes 9mm x 200' 010832B200

• 3 To 1 Shrink Ratio
• High Temperature Rating
• Stays Flexible

Hose/Wire Wrap

• Easy Installation And Removal
• Lightweight
• Self-Wrapping

Ignition Solder and Heat seal splice kit. Contains white, red, blue, and yellow for 26-10 AWG. Waterproof, Crimpless, 2:1 shrinkage ratio, Rated up to 600V, Temp. range from -67° to 220° F.

• 40 Piece Kit
• Temperature rated at -40° C to 105° C (-40° to 221° F)
• Starting Temperature of Soldering Melt: 115° C (239° F)

Lokjaw Locking Ties - 8" 9-Pack

• Locks down securely to prevent loosening, slipping, or failure
• Ideal for high-heat, high-vibration environments
• Constructed from high-grade 316 stainless steel

Male Pins and Seals

Male pins and seals for use with Weathertight Connectors.